ryobi electric planer manual

If damaged, have repaired by a qualified service technician at an authorized service facility. If any parts are damaged or missing do not operate this tool until the parts are replaced. When mounting the planer to a workbench, holes should be drilled through the supporting surface of the workbench. When properly cared for, it will give you years of rugged, trouble-free performance. Everyday eyeglasses have only impactresistant lenses, they are NOT safety glasses. OPERATION THICKNESS PLANING WARNING: Thickness planing sizes the workpiece to a desired thickness while creating a smooth, level surface. WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury. Use of any other parts may create a hazard or cause product damage. hitachi planer jointer combo wood table inch benchtop wen amp spiral hand thickness combination machine makita dws780 electric mount Do not allow familiarity with tools to make you careless. n Using the notched end of the magnetic blade wrench, remove the blade from the cutter head by hooking the notch over the end of the blade and pulling straight out. n Plane a scrap piece of wood and measure the depth of the finished piece. ryobi planer hand electric SPECIFIC SAFETY RULES n NEVER PUT YOUR FINGERS into the dust hood or under the cutter guard. ASSEMBLY UNPACKING WARNING: This product requires assembly. Planing Width . 13 in. Bevel Cut A cutting operation made with the blade at any angle other than 90 to the table surface. Thank you for your purchase. n Select the amount to be removed by rotating the depth adjustment handle. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal.

Please call 1-800-525-2579 for your nearest Authorized Service Center. The dust collection hood features a quick flip-up dumping door and a 2-1/4 in. MODEL NO. When mounting the planer to a mounting board, the board should be of sufficient size to avoid tipping while planer is in use. PORTABLE PLANER AP1301 SERVICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Authorized Service Center. n REPLACEMENT PARTS. Use clamps or a vise to hold work when practical. SYMBOL SIGNAL MEANING DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. MAINTENANCE n Using the open-end wrench, carefully loosen the blade locking screws ( 1 ). SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product.

OPERATION ADJUSTING THE PLANING DEPTH See Figure 7. OPERATORS MANUAL 13 in. Its safer than using your hand and frees both hands to operate tool. FEATURES KNOW YOUR PLANER DUST COLLECTION HOOD See Figure 2. TO REPLACE: n Unplug the planer and remove the switch key. Please study them and learn their meaning. PORTABLE PLANER AP1301 Your portable planer has been engineered and manufactured to our high standard for dependability, ease of operation, and operator safety. To avoid back injury, lift with your legs, not your back, and get help when needed. n Carefully remove the tool and any accessories from the box. For workpieces longer than 48 in. Torn grain Too deep a blade setting Workpiece being fed against grain Dull cutter blades Reduce depth of cut. NOTE: This tool is heavy. Place it on a level work surface. WARNING: Read and understand all instructions. OPERATORS MANUAL 13 in. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. The depth adjustment knob is used to set the amount of wood being removed in a planing pass. Failure to heed this warning could result in serious personal injury. ELECTRICAL EXTENSION CORDS SPEED AND WIRING Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole receptacles that accept the tools plug. Repair or replace a damaged or worn cord immediately. AND SERIAL NO. Whenever working with a new type of wood, make thin test cuts on a scrap piece of wood first to determine potential problems with the workpiece. When using a power tool at a considerable distance from the power source, use an extension cord heavy enough to carry the current that the tool will draw. Proper interpretation of these symbols will allow you to operate the tool better and safer. Worn blades will affect cutting accuracy and may produce ridges on the workpiece. The thickness of each cut will depend on the type of wood (hardwood versus softwood), width of workpiece, straightness, dryness, and grain composition. You can also check our web site at www.ryobitools.com for a complete list of Authorized Service Centers. Arbor The shaft on which a blade or cutting tool is mounted. n If you are changing to the second edge of the blade, rotate the blade end for end keeping the same flat side down. If the planer is to be used in a permanent location, it is recommended you secure it to a workbench or to a mounting board that can be easily clamped to a workbench or other stable surface. n DO NOT attempt to turn cutter head with hands. Motor 2 HP Peak Max. dust port for connecting to a shop vac. Butting workpieces end-toend as they are fed through the planer will minimize the problem, especially for shorter pieces, because it provides a more stable feed. n SECURE WORK. SYMBOLS Some of the following symbols may be used on this tool. ADJUSTMENTS WARNING: Before performing any adjustment, make sure the tool is unplugged from the power supply. Chamfer A cut removing a wedge from a block so the end (or part of the end) is angled rather than at 90. WARNING: To reduce the risk of injury, the user must read and understand the operators manual before using this product. TROUBLESHOOTING Problem Snipe (depressions at ends of workpiece) Possible Cause Dull cutter blades Incorrect butted stock Solution Unit not securely mounted Replace or turn cutter blades. Although snipe may be barely noticeable, it is important to keep the workpiece parallel and flat with the planer table to minimize snipe. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor. Replace or turn cutter blades. Two reversible high-speed blades provide twice the cutting life. The planer is equipped with two double-edged blades (replacement part number AC8630) attached to a rotating cutter head. An undersized extension cord will cause a drop in line voltage, resulting in a loss of power and causing the motor to overheat. All repairs, whether electrical or mechanical, should be made at your nearest authorized service center. DEPTH ADJUSTMENT HANDLE DEPTH ADJUSTING KNOB n Turn the depth adjusting knob until the zero on the knob aligns with the groove on the handle. Tighten lag bolts. n ALLOW THE CUTTER HEAD to reach full speed before using the planer. ASSEMBLY MOUNTING THE PLANER See Figure 4. OPERATION AVOIDING SNIPE POWER SWITCH Snipes, or depressions made at either end of a workpiece by cutter blades, can occur when the board is not properly supported. CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury. GLOSSARY OF TERMS Anti-Kickback Pawls (radial arm and table saws) A device which, when properly installed and maintained, is designed to stop the workpiece from being kicked back toward the front of the saw during a ripping operation. 15 AMP MOTOR HIGH-SPEED REVERSIBLE BLADES Your planer has a powerful 15 amp motor with sufficient power to handle tough cutting jobs. Be sure to provide all pertinent facts when you call or visit. TABLE OF CONTENTS n Introduction 2 n Warranty .. 2 n General Safety Rules . GENERAL SAFETY RULES n ALWAYS WEAR SAFETY GLASSES WITH SIDE SHIELDS. Use the magnet on the other end of the tool to help remove the blade from the planer ( 2 ). GENERAL SAFETY RULES n INSPECT TOOL CORDS PERIODICALLY. No Load Speed .. 10,000 RPM Max. When servicing, use only identical replacement parts. Planing Depth 1/8 in. Failure to heed this warning could result in serious personal injury. Feed other end of board first. Butt pieces end-to-end as they are fed into planer.

FEATURES PRODUCT SPECIFICATIONS Feed Rate .26 FPM Max Planing Height 6 in. TO ADJUST THE PLANING DEPTH: n Rotate the depth adjustment handle counterclockwise to lower the cutter head to the current depth of your workpiece.

n DONT OVERREACH. WARNING: n Lower the cutter head assembly. Inaccurate cuts can be prevented by routinely checking the alignment of the thickness scale. THICKNESS SCALE ADJUSTMENT See Figure 9. The thickness scale, located on the right front of the planer, shows the depth of the finished workpiece. Before attempting to use your portable planer, familiarize yourself with all the operating and safety requirements. MAINTENANCE BLADE REPLACEMENT WARNING: See Figure 12.
Page not found — Lebanon County Legal Journal


The page you requested was not found. You might want to read the following interesting articles.